| CLASSIC | front | rear | |||||||
| Type | Wheel set part n° | CLASSIC | offset | tyres | CLASSIC | offset | tyres | Type | requirements |
| 5 series (F07) | 37 07 0495 J | 9.5 x 22 | 18 | 265/30 ZR 22 | 10.5 x 22 | 28 | 295/25 ZR 22 | B | 2, 3, 4, 5, 6, 10 |
| Gran | 12, 13, 15 | ||||||||
| Turismo | 16, 17 | ||||||||
| anthracite | |||||||||
| 7 series | 37 01 0495 J | 9.5 x 22 | 25 | 265/30 ZR 22 | 10.5 x 22 | 28 | 295/25 ZR 22 | B | 1, 4, 6, 12, 16, 17 |
| (F01 / F02) | |||||||||
| anthracite | |||||||||
| 7 series | 37 65 1295 J | 9.5 x 22 | 28 | 265/30 ZR 22 | 10.5 x 22 | 21 | 295/25 ZR 22 | B | 1, 7, 11 |
| (E65 / E66) | |||||||||
| anthracite | |||||||||
| X5 (E70) | 37 70 0495 J | 9.5 x 22 | 28 | 265/35 ZR 22 | 10.5 x 22 | 21 | 295/30 ZR 22 | B | 9, 10, 12, 13 |
| anthracite | |||||||||
| X5 (E53) | 37 53 1295 J | 9.5 x 22 | 35 | 265/35 ZR 22 | 10.5 x 22 | 28 | 295/30 ZR 22 | B | |
| anthracite | |||||||||
| All HARTGE wheel sets can be equipped with Continental, Pirelli or Michelin tyres. / Technical data & prices subject to alterations | |||||||||
| All HARTGE wheel sets can be equipped with Tyre Pressure Control (TPC) and sets of lockable wheel bolts. | |||||||||
| Runflat System Component (RSC) tyres are available upon request. | |||||||||
1 - Reworking the rear wheel housing may be necessary (rolling the inside edge).
2 - Reworking the rear wheel housing is required (rolling the inside edge).
3 - Reworking the bumper panelling in the region of the wheel arch.
4 - Drawing out the rear wheel arches
5 - Repainting the rear wheel arches may be necessary.
6 - Pay attention to sufficient clearance in the front wheel housing (if necessary, rework the panelling of the wheel housing).
7 - Ensure a minimum clearance of 5 mm between the tire and the spring plate.
8 - A steering limiter is required.
9 - Only in conjunction with a spacer on each side of the rear axle.
10 - Only in conjunction with a spacer on each side of the front axle.
11 - Only in conjunction with a spacer on each side of the front and rear axle.
12 - Ensure to cover the tire tread sufficiently on side of the front axle.
13 - Ensure to cover the tire tread sufficiently on each side of the rear axle.
14 - Verification of speedometer required
15 - Pay attention to sufficient clearance in the rear wheel housing (if necessary, rework the panelling of the wheel housing).
16 - Reworking the front wheel housing may be necessary (rolling the inside edge).
17 - Drawing out the front wheel arches
18 - Verification of permissible front / rear axle load according to tire specification is essential. This varies from tire manufacturer to vehicle model.
Facebook
